Wheelchair Preparation

Original Editor - Your name will be added here if you created the original content for this page.

Top Contributors - Vidya Acharya, Naomi O'Reilly, Laura Ritchie, Kim Jackson, Amrita Patro and Jess Bell  

Introduction

The purpose of the Wheelchair Service Provision Guide is to provide an appropriate framework for identifying the essential steps in the provision of a wheelchair.If the components of the seating and mobility system originate from different manufacturers, the next step in wheelchair provision is product preparation.

Once equipment is received, the wheelchair base/frame, options, accessories, and seating and positioning components should be assembled and set-up according to the preliminary specifications detailed in the recommendation and selection process. This includes fabrication and installation of custom items and assessment of the function and operation of all mechanical and electronic components. An initial set up of electronic parameters, based on the client’s functional skills and abilities, should be performed if specialty power wheelchair controls have been recommended. If the components of the seating and mobility system originate from different manufacturers, the next step in wheelchair provision is product preparation. During this step, the wheelchair and its accessories and the seating and positioning components will be set up in accordance with the recommended specifications, based on the assessment and trial of equipment.

The objective of good practice in product preparation is to prepare the wheelchair for the fitting, including modifications or custom postural support component.

Product (wheelchair) preparation includes:

• preparing the wheelchair to match the wheelchair user’s prescription (selection);

• checking the wheelchair to make sure that it is safe and ready to be used and all parts are working properly. 

Preparing the wheelchair

Prepare the wheelchair in the following order:

1. Check that the wheelchair seat width and depth measurements are correct for the prescription   (selection).

2. Check that the cushion width and depth match the seat.

3. Adjust (where possible):

• Backrest height and angle;

• Armrests height;

• Rear wheels position;

• Brakes position;

• Footrests height;

• Push handles height;

• Any other adjustments.

4. Carry out a “wheelchair safe and ready” check.

Good practice in product preparation:

• Each wheelchair being prepared is labeled with the user’s name and a serial number or bar code.
• Modifications to wheelchairs (permanently altering the frame or a component of the wheelchair) are carried out only by personnel with the appropriate knowledge and skills, since any such modification may have structural and functional implications.
• The production and installation of custom seating systems or individual postural support components should be carried out by personnel with the appropriate knowledge and skills. This work should also be done in close collaboration with the assessment personnel.
• All mobility equipments should be checked for quality and safety before the user tries it.

Checklist: Is the wheelchair safe and ready to use?

For the whole wheelchair		How to check
There are no sharp edges		Check all over the wheelchair with eyes and hands
No parts are damaged or scratched.
The wheelchair travels in a straight line		Push the wheelchair away from you, making sure the castor wheels are in the “trail” position.
Front castor wheels
Spin freely.		Tip the wheelchair on to the back wheels. Spin the castor wheels.
Spin without touching the fork.
Bolts are tight.		Check. They should feel firm. Do not over tighten.
Front castor barrels
Castor fork spins freely.		Tip the wheelchair on to the back wheels. Spin the castor fork around.
Rear wheels
Spin freely.		Tip the wheelchair sideways on to one rear wheel. Spin the other wheel. Check the other side.
Axle bolts are tight.		Check. They should feel firm. Do not over tighten.
Tyres (if those are pneumatic) are inflated correctly.		Press on the tyres with your thumb. The wheel should depress a little, but no more than 5 mm.
Push rims are secure		Check
Brakes
Function properly		Apply brakes. Check the wheelchair cannot be moved.
Footrests
Footrests are securely attached.		Check.
Frame
Cross-folding wheelchair folds and unfolds easily.		Fold the wheelchair to check that the folding mechanisms are working correctly.
Fold-down backrest – the backrest folds and unfolds easily.
Cushion
The cushion is in the cover correctly.		Usually the cushion cover is done up at the back of the cushion, underneath.
The cushion is sitting on the wheelchair correctly.		If the cushion is contoured, the “well” for the seat bones should be at the back of the seat.
The cushion cover fabric is tight but not too tight.		The cushion cover should not stretch tightly over any contours of the cushion.
The cushion fully covers the seat		Check that no part of the seat is visible from under the cushion. This is particularly important for solid seats.

Sub Heading 3

References